the Anne Marie

  • the Anne Marie
  • Blog
    • Updates
    • Photos
    • Adventures
    • All
  • Gallery
  • Contact

2015/10/21 By nishi Leave a Comment

On the Can

As the cold weather began to seep into our nights (and now days), the toilet became a major necessity. Who wants to run nude 40 feet across the lawn in below freezing weather just to tinkle and run back? Or, less appealing, who wants to drag on clothes for this purpose, just to get naked again three minutes later? (Now your burning question is answered: I sleep in my birthday suit.)

So, as a most beloved gift to me, John took the lead on the construction of this nifty DIY composting toilet for us with just a few hours of work!

Isn’t she lovely?

DSC02306

It was quite simple, actually. He just followed these directions, added a couple of personal touches, and we are in business — literally.

He cut the pieces out of a nice board, but there wasn’t quite enough for the entirety. As you can see, the back is a bit short. Without compromising the integrity of the structure or its appearance and without having to buy another board for just the tiny bit that was lacking, we simply fastened the back at the top. Here, John is countersinking and screwing the back panel onto the top. This is what will hold the hinges to allow the box lid to lift when needed.

20150919_142200

Here, we have finished fastening all the pieces together. This shows a version of the design that can be done with crisp edges. We chose to round the top edges with a router before finishing, as you can see in the first photo.

20150919_143640

Next, we applied two thin layers of polyurethane to the lid and the box, including the edges, sanding between layers. The decision to poly the inside as well as the outside was based on the desire for ease of cleaning and to simply keep as much icky moisture out of the wood as possible.

IMG_20150922_155004084_HDR

Remarkably, the most difficult part of this project was changing the orientation of the supports of the seat. They have to be changed because they will sit awkwardly and wobbly on top of the edge of the bucket in their original direction. Turning them 90° allows for the supports to hug the outside of the bucket comfortably.

To change their orientation, first we pried them out of their holes with a flathead screwdriver. Next, we marked the depth of the original holes with some masking tape on the drill bit. Drilling the new holes was a bit tricky, but marking their placement with the pegs worked rather nicely.

DSC02304

And there you have it, folks!

DSC02307

We originally started by using composting bags; however, we immediately found that they did not work very well — the material is just too heavy. So we just dump it right onto the compost pile without a bag.

DSC02309

We have also been playing around with the cover material. Peat moss works well, but it is rather heavy. Corse saw dust from our brand new chain saw works well, too. That will most likely be our go-to for this purpose. We’ll need to cut firewood through the entire winter, so we won’t have to take up the space with a bulky bag of dirt if we go that route.

Either way, it has been working out very well, and we are happily to be able to poop in here. Now it is truly home.

Filed Under: Updates Tagged With: Construction, Toilet

2015/05/26 By John Leave a Comment

Thinking Ahead

We’re thinking ahead to Grey Fox this year. This is a nice memory from last year.

Filed Under: Photos Tagged With: Performance, Roof deck

2015/04/02 By John Leave a Comment

Light a Fire

With our hearth done, the next step is to make our wood stove usable. We need to run some stove pipe up and out of the roof. First, we secured the stove to the floor so we have a steady starting point. I’d never drilled into masonry before, but it turns out that with a masonry bit it’s pretty easy. Everything is easy with the right tools.

Masonry Drilling

Next we start building up the stove pipe from the back of the stove. This is the moment of truth, since I did my best to estimate the lengths necessary to vent the stove where we want it, but it was still just a guess.

DSC02057

Success! It landed right where we want it. The stove itself is located directly underneath a solar panel, so we can’t just have a straight pipe going up through the roof. We needed to come over a few feet to clear the panel. Yes, we could have moved the stove’s location, but we would have lost the ability to use the second starboard bench as a bed. It would have simply been too short.

DSC02058

So we cut a hole in the wood, then in the metal roof.

DSC02061

Then we cut a hole in the deck.

DSC02062

To keep any water from getting inside, we used the manufacturer’s flashing and some Henry’s roof tar. I was really impressed with this stuff, and would have used it far more often had I been familiar with it.

DSC02078

We finished by running the pipe all the way up and out the deck. The pipe has double wall construction and 1″ clearances to combustibles. I’ve made sure to test this part of the deck while the stove is running and it stays very cool.

DSC02077

We’re using their basic chimney cap up top. It seems to have no issues with either wind or rain so far. The last foot of pipe and the cap itself are able to be removed for travel.

20150402_112531

Inside, we covered the ceiling hole with another piece of the DuraVent flashing. Nishi trimmed it to a perfect circle, and it looks great.

20150402_112456

All that was left was to actually start her up!

20150227_115304

The stove burns very nicely and, as advertised, we have a smokeless burn in around twenty minutes. I’m still playing around with finding the perfect fuel. The wood needs to be cut much shorter than anything I’m used to, and I haven’t found the sweet spot yet. I have found that the compressed sawdust logs I’ve used in larger wood stoves don’t work that well in here.

We still need insulating curtains over the windows to hold the heat generated by this little stove. The heat difference at the ceiling above the windows is dramatic, and along with a few small circulating fans the curtains will make this quite the toasty space.

Filed Under: Updates Tagged With: Chimney, Construction, Hearth, Woodstove

2014/11/09 By John Leave a Comment

Hearth

Every home needs a hearth. It’s the beating heart of a living space. Our bus is no exception.

Our hearth is almost purely for aesthetics. The Kimberly woodstove we’re using has ridiculously tiny clearances, and we have given it much more room than is necessary. In addition, the vent pipe we’re using only has a 1″ clearance to combustibles, so let me preface all this by saying the space we’ve allocated is overkill.

We left a nearly 3′ by 3′ space between the two starboard benches, with the plan of fitting our woodstove right in the middle. Since we’re in a relatively tiny space, I made a hole in the floor for external combustion air. On top of that, we cut and attached our cement board. While the cement board could be helpful to deal with the heat, in practice it’s really just to keep the masonry in place while the wood elsewhere expands and contracts.

DSC01926.jpg

We’re using a thin cut brick for our hearth. They’re smaller than standard bricks, which works to our advantage. The thinner/smaller the building materials we’re able to use the more space we appear to have inside. We attached them to the cement board with Liquid Nails.

DSC01929.jpg

While Nishi was able to space out the bricks on the floor without a guide, we needed to cut some small spacers for our walls. Neither of us remember figuring this out in advance, but our hearth measurements perfectly accommodate our bricks. We didn’t need to make any tough cuts.

DSC01941.jpg

Our hearth looked pretty cool with bricks alone, but it still needed mortar between those joints.

DSC01947.jpg

The joints between our bricks are smaller than most, in part because our bricks are narrower to start. We tried at first using a tiny clay sculpting tool to lay the mortar, but it was imprecise and slow. We just adopted the finger-painting method. A word of warning to anyone who decides to give this a try: do not take breaks. The mortar dries your skin really quickly and will wear through your fingers before you realize it.

DSC01963.jpg

We let it sit a few days, then brushed and vacuumed away whatever was loose. It came out pretty clean.

DSC01985.jpg

Our stove will be sitting nearly dead center in the square. Again, total overkill for both stove and pipe clearances, but it’ll give us a good spot to store other stove-related items.

DSC01994.jpg

We had some brick left over, and used it to make a little accent wall along our counter.

DSC01997.jpg

Things are coming together, and as soon as the stove is good to go, we’ll be secure in our ability to work through the winter. Nishi took this fantastic picture one night after work.

DSC01949.jpg

Filed Under: Updates Tagged With: Brick, Hearth, Woodstove

  • « Previous Page
  • 1
  • 2
  • 3
  • 4
  • …
  • 9
  • Next Page »

Categories

  • Adventures
  • Photos
  • Updates

Tags

Anxiety Bed Brick Ceiling Chimney Clearance lights Compost Construction Cooktop Counter Demolition Desk Festivals Flooring floorplan Fridge Hearth Inspiration Insulation Kitchen Leaks Lights Performance Port Bench Roof Roof deck Rust Sink Snow Toilet Tour Upholstery Video Walls Water Heater Woodstove

Other Conversions

  • La Casita
  • Outside Found
  • A Buffalo Bus
  • Would you look at that bus?
  • guydogbus
  • Wild Blue
  • the Juan Way Tour
See The Full List

Resources

  • BusConversions.com
  • Cheap RV Living
  • Tiny House Blog
  • Schoolbus Homes
  • Skoolie.net
  • /r/skoolies
  • Skoolie Converters
  • faircompanies.com

Categories

  • Adventures
  • Photos
  • Updates

Tags

Anxiety Bed Brick Ceiling Chimney Clearance lights Compost Construction Cooktop Counter Demolition Desk Festivals Flooring floorplan Fridge Hearth Inspiration Insulation Kitchen Leaks Lights Performance Port Bench Roof Roof deck Rust Sink Snow Toilet Tour Upholstery Video Walls Water Heater Woodstove
Text and photos of the Anne Marie on bus.life are licensed under a Creative Commons Attribution License. Use it.
This is Clear.Design